Project

General

Profile

strongSwan smart card configuration HOWTO » History » Version 32

« Previous - Version 32/159 (diff) - Next » - Current version
Jean-Michel Pouré, 26.12.2009 21:51


strongSwan for Smart cards HOWTO

Smartcards are a mature technology, which intruduce Two-Factor authentication and avoid your CA from being stolen by a theft.

Introduction

Supported smartcards

opensc supports a variety of smart card readers.

GNU/Linux supports most USB smartcard readers following CCID standard. Especially, there is very good support for Omnikey card readers.

  • Second hand Omnikey 3121 CardMan USB and Omnikey 4040 PCMCIA smartcard readers can be found on eBay for less than 10 euros.
  • Smartcard readers with an integrated PIN pad offer an increased security level because the PIN entry cannot be sniffed on the host computer e.g. by a surrepticiously installed key logger. The Omnikey 3821 secure smartcard reader with LCD display and keypad for secure PIN entry may be a good choice [anyone using it?].
  • Cryptoflex 32k blank cards are a common choice.

Read Buyers Guide section in opensc FAQ for more information.

Software requirements

To install pcsc-tools under Debian based distributions:

apt-get install pcsc-tools

If you own an Omnikey USB reader:

apt-get install pcsc-omnikey

strongSwan supports PKCS#11 RSA standard using opensc libraries, which specifies how to store cryptographic information on devices.

To install opensc u

sudo apt-get install opensc

To enable smart card support in strongSwan, you may need to compile from sources:

./configure <add your options there> \
--enable-smartcard
make
sudo make install

Installing and configuring the smartcard reader

Certification Authority

We recommend using a certificate GUI to set-up your CA. One important thing to keep in mind is that, you shouldn't create private keys with a length not supported by your smart card (check the specs to be sure). Keys with a maximum length is 2048 bits are known to work.

Initialisation of cards

Check that the card reader is correctly recognized by OpenSC:

$ opensc-tool -l
Readers known about:
Nr.    Driver     Name
0      pcsc       OmniKey CardMan 3121 00 00
1      openct     OpenCT reader (detached)
2      openct     OpenCT reader (detached)
3      openct     OpenCT reader (detached)
4      openct     OpenCT reader (detached)
5      openct     OpenCT reader (detached)

At nr. 0 we have our recognized Omnikey CardMan 3121 reader. Let's insert our smart card in the reader (note that when buying the card you'll also receive the TRANSPORT KEY. Make sure that the transport key proposed by OpenSC matches the one you got in the mail. You will destroy the card by entering the wrong Key three times):

Let's double check that the card is recongized by printing its ATR:

$ opensc-tool -r0 -a
3b:95:18:40:ff:62:04:01:01:05

We can also check the name of the card with the -n switch (we can omit the -r0 since we only have one reader connected):

$ opensc-tool -n
Cryptoflex 32K e-gate v4

At this point we know both the card and reader are fully recognized and functional, and we can proceed to erase the card: (You will be asked for the transport key you got in your mail)

$ pkcs15-init -E

Transport key (External authentication key #1) required.
Please enter key in hexadecimal notation (e.g. 00:11:22:aa:bb:cc),
or press return to accept default.

To use the default transport keys without being prompted,
specify the --use-default-transport-keys option on the
command line (or -T for short), or press Ctrl-C to abort.
Please enter key [2c:15:e5:26:e9:3e:8a:19]:

Now we Initialize the card and we format it the PKCS#15 way. We will be prompted for Security Officer PIN, User Unblocking PIN (PUK) and Transport Key:

$ pkcs15-init --create-pkcs15
Please enter Security Officer PIN:
Please type again to verify:
Unblock Code for New User PIN (Optional - press return for no PIN).
Please enter User unblocking PIN (PUK):
Please type again to verify:
Transport key (External authentication key #1) required.
Please enter key in hexadecimal notation (e.g. 00:11:22:aa:bb:cc),
or press return to accept default.

To use the default transport keys without being prompted,
specify the --use-default-transport-keys option on the
command line (or -T for short), or press Ctrl-C to abort.
Please enter key [2c:15:e5:26:e9:3e:8a:19]:

Storing the private key on the card

Now we'll add a PIN for the label "Michele Baldessari" and we'll associate the 01 auth id to it. We'll be prompted for the Security Officer Pin inserted one step above :

$ pkcs15-init --store-pin --auth-id 01 --label "Michele Baldessari" 
New User PIN.
Please enter User PIN:
Please type again to verify:
Unblock Code for New User PIN (Optional - press return for no PIN).
Please enter User unblocking PIN (PUK):
Please type again to verify:
Security officer PIN required.
Please enter Security officer PIN:
Transport key (External authentication key #1) required.
Please enter key in hexadecimal notation (e.g. 00:11:22:aa:bb:cc),
or press return to accept default.

To use the default transport keys without being prompted,
specify the --use-default-transport-keys option on the
command line (or -T for short), or press Ctrl-C to abort.
Please enter key [2c:15:e5:26:e9:3e:8a:19]:

Now we can check the PINs stored on the card:

$ pkcs15-tool --list-pins
PIN [Security Officer PIN]
        Com. Flags: 0x3
        ID        : ff
        Flags     : [0xB2], local, initialized, needs-padding, soPin
        Length    : min_len:6, max_len:8, stored_len:8
        Pad char  : 0x00
        Reference : 2
        Type      : ascii-numeric
        Path      : 3f005015

PIN [Michele Baldessari]
        Com. Flags: 0x3
        ID        : 01
        Flags     : [0x32], local, initialized, needs-padding
        Length    : min_len:4, max_len:8, stored_len:8
        Pad char  : 0x00
        Reference : 1
        Type      : ascii-numeric
        Path      : 3f0050154b01

Now we'll store the client Certificate (stored in a PKCS#12 file name client-cert.p12) on the card and we associate it to auth-id 01, which we just created:

$ pkcs15-init -S client-cert.p12 -f PKCS12 -a 01
error:23076071:PKCS12 routines:PKCS12_parse:mac verify failure
Please enter passphrase to unlock secret key:
Importing 2 certificates:
  0: /C=IT/ST=Bozen/L=Sterzing/O=Foo/CN=Michele/emailAddress=michele@pupazzo.org
  1: /C=IT/ST=Bozen/L=Sterzing/O=Foo/CN=CA VPN/emailAddress=ca@pupazzo.org
Security officer PIN required.
Please enter Security officer PIN:
User PIN required.
Please enter User PIN:
Security officer PIN required.
Please enter Security officer PIN:

(We're asked for the PKCS#12 private key password, the Security Officer Pin and the User pin)

At this point we're set and the key is on the smartcard protected with a user pin from reading and with a security officer pin from writing.

You can double-check the certificates on the smart card with:

$ pkcs15-tool -c
X.509 Certificate [/C=IT/ST=Bozen/L=Sterzing/O=Foo/CN=Michele/emailAddress=michele@pupazzo.org]
        Flags    : 2
        Authority: no
        Path     : 3f0050154545
        ID       : 45

X.509 Certificate [/C=IT/ST=Bozen/L=Sterzing/O=Foo/CN=CA VPN/emailAddress=ca@pupazzo.org]
        Flags    : 2
        Authority: yes
        Path     : 3f0050154546
        ID       : 46

And the keys with:

$ pkcs15-tool -k
Private RSA Key [Private Key]
        Com. Flags  : 3
        Usage       : [0x2C], sign, signRecover, unwrap
        Access Flags: [0x1D], sensitive, alwaysSensitive, neverExtract, local
        ModLength   : 2048
        Key ref     : 0
        Native      : yes
        Path        : 3f0050154b0130450012
        Auth ID     : 01
        ID          : 45

strongSwan configuration

Acknowledgements

This article was adapted by Smartcard HOWTO written by Michele Baldessari. I contact the author for authorization and licence of the text.