forecast Plugin » History » Version 2
The forecast plugin uses Linux Netfilter marks to allow identical IPsec policies having multicast or broadcast selectors, and uses a listen-and-forward mechanism to forward such traffic over all matching SAs. It supports forwarding of multi/broadcast traffic between multiple connected clients and between clients and a LAN attached to the IPsec gateway.
The plugin is disabled by default and can be enabled on Linux builds by adding
--enable-forecastto the ./configure options.
Building the plugin requires iptables development headers to be installed.
The plugin has been introduced in strongSwan 5.3.0.
The forecast plugin currently is used on any SA negotiated that uses a unique mark. To configure such a connection as responder, set a unique mark, and don't forget to include the broadcast/multicast selectors that you want to forward:
conn conn-with-mc-bc leftsubnet=10.1.0.0/16,184.108.40.206/4 rightsourceip=10.1.0.128/26 rightsubnet=%dynamic,220.127.116.11/4,10.1.255.255 mark=%unique # ....
The leftsubnet shall include the local network and any multicast address to tunnel, but can also be 0.0.0.0/0. The client subnet can include multicast addresses as well, and the required broadcast addresses. Don't forget to include the default %dynamic selector if a virtual IP address is assigned to the client.
A unique mark per negotiated SA is required, so the SAs can be distinguished. The plugin automatically configures Netfilter rules in the mangle table to send mutlicast/broadcast packets over multiple SAs.
Some additional global strongswan.conf options are used by the forecast plugin:
|Comma separated list of multicast groups to join locally. The local host receives and forwards packets in the local LAN for joined multicast groups only. Packets matching the list of multicast groups get forwarded to connected clients. The default group includes host multicasts, IGMP, mDNS, LLMNR and SSDP/WS-Discovery, and is usually a good choice for Windows clients.|
|Name of the local interface to listen for broadcasts messages to forward. If no interface is configured, the first usable interface is used, which is usually just fine for single-homed hosts. If your host has multiple interfaces, set this option to the local LAN interface you want to forward broadcasts from/to.|
|Comma separated list of CHILD_SA configuration names for which to perform multi/broadcast reinjection. For clients connecting over such a configuration, any multi/broadcast received over the tunnel gets reinjected to all active tunnels. This makes the broadcasts visible to other peers, and for examples allows clients to see others shares. If disabled, multi/broadcast messages received over a tunnel are injected to the local network only, but not to other IPsec clients.|
Netfilter rules and marks¶
In PREROUTING, a gateway applies the unique mark assigned to the SA to the packet. This makes sure the IPsec policy actually matches, as we require the correct mark for a policy match. For non-NAT situations, ESP matching is used to MARK packets, for NAT situations the packets get selected based on UDP encapsulation ports.
Additionally, PREROUTING rules get installed to set the mark on decapsulated traffic matching any policy.
On the OUTPUT chain, the MARK target is used to set the mark to match the appropriate IPsec policy.
The rules installed by the plugin for two clients looks something like:
Chain PREROUTING (policy ACCEPT 55 packets, 8648 bytes) pkts bytes target prot opt in out source destination 1 112 MARK all -- * * 0.0.0.0/0 10.1.0.130 MARK set 0x2 3 488 MARK esp -- * * 192.168.0.200 192.168.0.1 esp spi:3242273483 MARK set 0x2 1 112 MARK all -- * * 0.0.0.0/0 10.1.0.129 MARK set 0x1 3 488 MARK esp -- * * 192.168.0.100 192.168.0.1 esp spi:3416575175 MARK set 0x1 Chain INPUT (policy ACCEPT 50 packets, 8172 bytes) pkts bytes target prot opt in out source destination Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 65 packets, 10840 bytes) pkts bytes target prot opt in out source destination 0 0 MARK all -- * * 0.0.0.0/0 10.1.0.130 MARK set 0x2 0 0 MARK all -- * * 0.0.0.0/0 10.1.0.129 MARK set 0x1