ipsec.conf: conn Reference » History » Version 59

Tobias Brunner, 31.01.2013 11:03

1 50 Tobias Brunner
{{title(ipsec.conf: conn Reference)}}
2 49 Tobias Brunner
3 49 Tobias Brunner
h1. ipsec.conf: conn <name>
4 1 Martin Willi
5 44 Tobias Brunner
6 1 Martin Willi
7 44 Tobias Brunner
h2. General Connection Parameters
8 21 Andreas Steffen
9 36 Andreas Steffen
_aaa_identity = <id>_
10 36 Andreas Steffen
11 36 Andreas Steffen
p((. defines the identity of the AAA backend used during IKEv2 EAP authentication. This is required if
12 36 Andreas Steffen
     the EAP client uses a method that verifies the server identity (such as EAP-TLS), but it does not
13 36 Andreas Steffen
     match the IKEv2 gateway identity.
14 36 Andreas Steffen
15 58 Tobias Brunner
_aggressive = yes | *no*_
16 58 Tobias Brunner
17 58 Tobias Brunner
p((. whether to use IKEv1 Aggressive or Main Mode (the default). Available since [[5.0.0]].
18 58 Tobias Brunner
19 31 Martin Willi
_also = <section name>_
20 1 Martin Willi
21 57 Tobias Brunner
p((. includes conn section <name>.
22 1 Martin Willi
23 58 Tobias Brunner
_authby = *pubkey* | rsasig | ecdsasig | psk | secret | xauthrsasig | xauthpsk | never_
24 24 Andreas Steffen
25 31 Martin Willi
p((. how the two security gateways should authenticate each other; acceptable values are *secret* or *psk*
26 58 Tobias Brunner
     for pre-shared secrets, *pubkey* (the default) for public key signatures as well as the synonyms *rsasig*
27 58 Tobias Brunner
     for RSA digital signatures and *ecdsasig* for Elliptic Curve DSA signatures.
28 58 Tobias Brunner
     *never*  can be used if negotiation is never to be attempted or accepted (useful for shunt-only conns).
29 58 Tobias Brunner
     Digital signatures are superior in every way to shared secrets. IKEv1 additionally supports the values
30 58 Tobias Brunner
     *xauthpsk* and *xauthrsasig* that will enable _eXtended Authentication (XAuth)_ in addition to IKEv1 main
31 58 Tobias Brunner
     mode based on shared secrets or digital RSA signatures,  respectively.
32 58 Tobias Brunner
     This parameter is deprecated for IKEv2 connections (and IKEv1 connections since [[5.0.0]]), as two peers
33 58 Tobias Brunner
     do not need to agree on an authentication method. Use the _left|rightauth_ parameter instead to define
34 58 Tobias Brunner
     authentication methods.
35 1 Martin Willi
36 31 Martin Willi
_auto = *ignore* | add | route | start_
37 23 Tobias Brunner
38 1 Martin Willi
p((. what operation, if any, should be done automatically at IPsec startup. *add* loads a connection without
39 21 Andreas Steffen
     starting it. *route* loads a connection and installs kernel traps. If traffic is detected between
40 21 Andreas Steffen
     _leftsubnet_ and _rightsubnet_, a connection is established. *start* loads a connection and brings
41 58 Tobias Brunner
     it up immediately. *ignore* ignores the connection. This is equal to deleting a connection from the config
42 57 Tobias Brunner
     file. Relevant only locally, other end need not agree on it.
43 1 Martin Willi
44 23 Tobias Brunner
_closeaction = *none* | clear | hold | restart_
45 47 Tobias Brunner
46 47 Tobias Brunner
p((. defines the action to take if the remote peer unexpectedly closes a CHILD_SA (IKEv2 only, see _dpdaction_ for
47 47 Tobias Brunner
     meaning of values). A _closeaction_ should not be used if the peer uses reauthentication or uniqueids checking,
48 57 Tobias Brunner
     as these events might trigger the defined action when not desired.
49 47 Tobias Brunner
50 23 Tobias Brunner
_compress = yes | *no*_
51 31 Martin Willi
52 23 Tobias Brunner
p((. whether IPComp compression of content is proposed on the connection (link-level compression does not work on
53 57 Tobias Brunner
     encrypted data, so to be effective, compression must be done before encryption). A value of *yes* causes the daemon
54 57 Tobias Brunner
     to propose both compressed and  uncompressed, and  prefer compressed. A value of *no* prevents the daemon from proposing or accepting compression.
55 1 Martin Willi
56 21 Andreas Steffen
_dpdaction = *none* | clear | hold | restart_
57 21 Andreas Steffen
58 21 Andreas Steffen
p((. controls the use of the Dead Peer Detection protocol (DPD, RFC 3706) where R_U_THERE notification messages
59 1 Martin Willi
     (IKEv1) or empty INFORMATIONAL messages (IKEv2) are periodically sent in order to check the liveliness of the
60 1 Martin Willi
     IPsec peer. The values *clear*, *hold*, and *restart* all activate DPD. If no activity is detected,
61 1 Martin Willi
     all  connections with a dead peer are stopped and unrouted (*clear*), put in the hold state (*hold*)
62 57 Tobias Brunner
     or restarted (*restart*). The default is *none* which disables the active sending of DPD messages.
63 21 Andreas Steffen
64 21 Andreas Steffen
_dpddelay = *30s* | <time>_
65 41 Tobias Brunner
66 1 Martin Willi
p((. defines  the  period time interval with which R_U_THERE messages/INFORMATIONAL exchanges are sent to the peer.
67 31 Martin Willi
     These are only sent if no other traffic is received. In IKEv2, a value of 0 sends no additional INFORMATIONAL
68 1 Martin Willi
     messages and uses only standard messages (such as those to rekey) to detect dead peers.
69 30 Martin Willi
70 31 Martin Willi
_dpdtimeout = *150s* | <time>_
71 30 Martin Willi
72 30 Martin Willi
p((. defines the timeout interval, after which all connections to a peer are deleted in case of inactivity.
73 54 Andreas Steffen
     This only applies to IKEv1, in IKEv2 the default [[Retransmission|retransmission timeout]] applies, as every exchange is used to
74 23 Tobias Brunner
     detect dead peers.
75 41 Tobias Brunner
76 1 Martin Willi
_inactivity = <time>_
77 1 Martin Willi
78 55 Andreas Steffen
p((. defines the timeout interval, after which a CHILD_SA is closed if it did not send or receive any traffic.
79 57 Tobias Brunner
     Supported only for IKEv2 connections prior to [[5.0.0]].
80 21 Andreas Steffen
81 1 Martin Willi
_eap_identity = <id>_
82 1 Martin Willi
83 41 Tobias Brunner
p((. defines the identity the client uses to reply to an EAP Identity request. If defined on the EAP server, the defined
84 1 Martin Willi
     identity  will be used as peer identity during EAP authentication. The special value _%identity_ uses the EAP Identity method
85 23 Tobias Brunner
     to ask the client for a EAP identity. If not defined, the IKEv2 identity will be used as EAP identity.
86 1 Martin Willi
87 31 Martin Willi
_esp = <cipher suites>_
88 23 Tobias Brunner
89 14 Martin Willi
p((. comma-separated list of ESP encryption/authentication algorithms to be used for the connection, e.g.
90 1 Martin Willi
     _aes128-sha256_. The notation is _encryption-integrity[-dhgroup][-esnmode]_.
91 1 Martin Willi
     Defaults to *aes128-sha1,3des-sha1*. The daemon adds its extensive default proposal to
92 57 Tobias Brunner
     this default or the configured value. To restrict it to the configured proposal an exclamation mark (*&#33;*)
93 48 Tobias Brunner
     can be added at the end.
94 48 Tobias Brunner
     *Note*: As a responder both daemons accept the first supported proposal received from the peer. In order
95 51 Tobias Brunner
     to restrict a responder to only accept specific cipher suites, the strict flag (*&#33;*, exclamation mark)
96 48 Tobias Brunner
     can be used, e.g: _aes256-sha512-modp4096!_
97 58 Tobias Brunner
     If _dh-group_ is specified, CHILD_SA setup and rekeying include a separate Diffe-Hellman exchange (since
98 58 Tobias Brunner
     [[5.0.0]] this also applies to IKEv1 Quick Mode).
99 48 Tobias Brunner
     Valid values for _esnmode_ (IKEv2 only) are _esn_ and _noesn_.  Specifying both negotiates extended sequence
100 1 Martin Willi
     number support with the peer, the default is *noesn*.
101 1 Martin Willi
     Refer to [[IKEv1CipherSuites]] and [[IKEv2CipherSuites]] for a list of valid keywords.
102 1 Martin Willi
103 1 Martin Willi
_forceencaps = yes | *no*_
104 48 Tobias Brunner
105 48 Tobias Brunner
p((.  force UDP encapsulation for ESP packets even if no NAT situation is detected.
106 43 Tobias Brunner
      This may help to surmount restrictive firewalls. In order to force the peer to
107 57 Tobias Brunner
      encapsulate packets, NAT detection payloads are faked.
108 1 Martin Willi
      Only supported for IKEv2 prior to [[5.0.0]].
109 1 Martin Willi
110 31 Martin Willi
_ike = <cipher suites>_
111 1 Martin Willi
112 1 Martin Willi
p((. comma-separated list of IKE/ISAKMP SA encryption/authentication algorithms to be used, e.g.
113 59 Tobias Brunner
     _aes128-sha1-modp2048_. The notation is _encryption-integrity[-prf]-dhgroup_. In IKEv2, multiple algorithms
114 1 Martin Willi
     and proposals may be included, such as _aes128-aes256-sha1-modp1536-modp2048,3des-sha1-md5-modp1024_.
115 59 Tobias Brunner
116 59 Tobias Brunner
p((. The ability to configure a PRF algorithm different to that defined for integrity protection was added with [[5.0.2]].
117 59 Tobias Brunner
     If no PRF is configured, the algorithms defined for integrity are proposed as PRF.  The prf keywords are the same as
118 59 Tobias Brunner
     the integrity algorithms, but have a _prf_ prefix (such as _prfsha1_, _prfsha256_ or _prfaesxcbc_).
119 59 Tobias Brunner
120 59 Tobias Brunner
p((. Defaults to *aes128-sha1-modp2048,3des-sha1-modp1536* for IKEv1. The daemon adds its extensive default proposal
121 59 Tobias Brunner
     to this default or the configured value. To restrict it to the configured proposal an exclamation mark (*&#33;*) can be added at the end.
122 59 Tobias Brunner
     Refer to [[IKEv1CipherSuites]] and [[IKEv2CipherSuites]] for a list of valid keywords.
123 59 Tobias Brunner
124 59 Tobias Brunner
p((. *Note*: As a responder both daemons accept the first supported proposal received from the peer. In order
125 51 Tobias Brunner
     to restrict a responder to only accept specific cipher suites, the strict flag (*&#33;*, exclamation mark)
126 48 Tobias Brunner
     can be used, e.g: _aes256-sha512-modp4096!_
127 51 Tobias Brunner
128 48 Tobias Brunner
_ikelifetime = *3h* | <time>_
129 43 Tobias Brunner
130 58 Tobias Brunner
p((. how long the keying channel of a connection (_ISAKMP or IKE SA_) should last before being renegotiated.
131 58 Tobias Brunner
     Also see [[ExpiryRekey|Expiry and Rekey]].
132 31 Martin Willi
133 40 Tobias Brunner
_installpolicy = *yes* | no_
134 1 Martin Willi
135 58 Tobias Brunner
p((. decides whether IPsec policies are installed in the kernel by the charon daemon for a given connection.
136 31 Martin Willi
     Allows peaceful cooperation e.g. with the Mobile IPv6  _mip6d_ daemon who wants to control the kernel policies.
137 23 Tobias Brunner
138 21 Andreas Steffen
_keyexchange = *ike* | ikev1 | ikev2_
139 1 Martin Willi
140 23 Tobias Brunner
p((. method of key exchange; which protocol should be used to initialize the connection.
141 58 Tobias Brunner
     Prior to [[5.0.0]] connections marked with *ikev1*  were initiated with Pluto, those marked with *ikev2* with Charon.
142 58 Tobias Brunner
     An incoming request from the remote peer was handled by the correct daemon, unaffected from the _keyexchange_ setting.
143 57 Tobias Brunner
     Starting with strongSwan [[4.5.0]] the default value *ike* is a synonym for *ikev2*, whereas in older strongSwan releases *ikev1* was assumed.
144 57 Tobias Brunner
     Since [[5.0.0]] both protocols are handled by Charon and connections marked with *ike* will use IKEv2 when initiating, but accept any protocol version when responding.
145 38 Andreas Steffen
146 38 Andreas Steffen
_keyingtries = *3* | <number> | %forever_
147 20 Andreas Steffen
148 45 Tobias Brunner
p((. how  many attempts (a positive integer or _%forever_) should be made to negotiate a connection, or a replacement
149 31 Martin Willi
     for one, before giving up (default 3). The value _%forever_ means 'never give up'.  Relevant  only  locally, other end need
150 46 Daniel Mentz
     not agree on it.
151 45 Tobias Brunner
152 1 Martin Willi
153 26 Tobias Brunner
154 31 Martin Willi
p((. synonym for _lifetime_.
155 26 Tobias Brunner
156 26 Tobias Brunner
_lifebytes = <number>_
157 31 Martin Willi
158 57 Tobias Brunner
p((. the number of bytes transmitted over an IPsec SA before it expires (prior to [[5.0.0]] only for IKEv2).
159 26 Tobias Brunner
160 26 Tobias Brunner
_lifepackets = <number>_
161 1 Martin Willi
162 57 Tobias Brunner
p((. the number of packets transmitted over an IPsec SA before it expires (prior to [[5.0.0]] only for IKEv2).
163 1 Martin Willi
164 31 Martin Willi
_lifetime = *1h* | <time>_
165 26 Tobias Brunner
166 31 Martin Willi
p((. how  long  a  particular  instance  of a connection (a set of encryption/authentication keys for user packets)
167 1 Martin Willi
     should last, from successful negotiation to expiry; acceptable values are an integer optionally followed by
168 1 Martin Willi
     _s_ (a time in seconds) or a decimal number followed by _m_, _h_, or _d_ (a time in minutes, hours,
169 21 Andreas Steffen
     or days respectively) (default _1h_, maximum _24h_).  Normally, the connection is renegotiated (via the
170 1 Martin Willi
     keying  channel) before it expires (see _margintime_).  The two ends need not exactly agree on _lifetime_, although if they
171 1 Martin Willi
     do not, there will be some clutter of superseded connections on the end which thinks the lifetime is longer.
172 1 Martin Willi
     Also see [[ExpiryRekey|Expiry and Rekey]].
173 40 Tobias Brunner
174 1 Martin Willi
_marginbytes = <number>_
175 26 Tobias Brunner
176 57 Tobias Brunner
p((. how many bytes before IPsec SA expiry (see _lifebytes_) should attempts to negotiate a replacement begin.
177 26 Tobias Brunner
178 26 Tobias Brunner
_marginpackets = <number>_
179 26 Tobias Brunner
180 57 Tobias Brunner
p((. how many packets before IPsec SA expiry (see _lifepackets_) should attempts to negotiate a replacement begin.
181 26 Tobias Brunner
182 40 Tobias Brunner
_margintime = *9m* | <time>_
183 1 Martin Willi
184 1 Martin Willi
p((. how long before connection expiry or keying-channel expiry should attempts to negotiate a replacement begin; acceptable values
185 26 Tobias Brunner
     as for _lifetime_ (default _9m_).  Relevant only locally, other end need not agree on it. Also see [[ExpiryRekey|Expiry and Rekey]].
186 35 Andreas Steffen
187 35 Andreas Steffen
_mark = <value>[/<mask>]_
188 37 Tobias Brunner
189 35 Andreas Steffen
p((. sets  an XFRM mark in the inbound and outbound IPsec SAs and policies. If the mask is missing then
190 39 Gerd v. Egidy
     a default mask of *0xffffffff* is assumed.
191 35 Andreas Steffen
192 57 Tobias Brunner
_mark_in = <value>[/<mask>]_
193 1 Martin Willi
194 1 Martin Willi
p((. sets an XFRM mark in the inbound IPsec SA and policy. If the mask is missing then
195 57 Tobias Brunner
     a default mask of *0xffffffff* is assumed.
196 57 Tobias Brunner
197 39 Gerd v. Egidy
_mark_out = <value>[/<mask>]_
198 35 Andreas Steffen
199 1 Martin Willi
p((. sets an XFRM mark in the outbound IPsec SA and policy. If the mask is missing then
200 23 Tobias Brunner
     a default mask of *0xffffffff* is assumed.
201 31 Martin Willi
202 21 Andreas Steffen
_mobike = *yes* | no_
203 1 Martin Willi
204 1 Martin Willi
p((. enables the IKEv2 [[MobIke|MOBIKE]] protocol defined by RFC 4555. If set to *no*, the charon
205 23 Tobias Brunner
     daemon will not actively propose [[MobIke|MOBIKE]] as initiator and ignore the MOBIKE_SUPPORTED
206 31 Martin Willi
     notify as responder.
207 23 Tobias Brunner
208 57 Tobias Brunner
_modeconfig = push | *pull*_
209 21 Andreas Steffen
210 1 Martin Willi
p((. defines which mode is used to assign a virtual IP. Currently relevant for IKEv1 only since IKEv2 always uses
211 1 Martin Willi
     the configuration payload in *pull* mode. Cisco VPN gateways usually operate in *push* mode.
212 23 Tobias Brunner
     The charon daemon currently does not support push mode, hence with [[5.0.0]] this parameter has no effect.
213 57 Tobias Brunner
214 21 Andreas Steffen
_reauth = *yes* | no_
215 31 Martin Willi
216 20 Andreas Steffen
p((. whether rekeying of an IKE_SA should also reauthenticate the peer. In IKEv1, reauthentication is always done.
217 1 Martin Willi
     In  IKEv2, a value of *no* rekeys without uninstalling the IPsec SAs, a value of *yes* (the default)
218 23 Tobias Brunner
     creates a new IKE_SA from scratch and tries to recreate all IPsec SAs.
219 23 Tobias Brunner
220 1 Martin Willi
_rekey = *yes* | no_
221 1 Martin Willi
222 1 Martin Willi
p((. whether a connection should be renegotiated when it is about to expire. The two ends need not agree, but
223 1 Martin Willi
     while a value of no prevents the daemon from requesting renegotiation, it does not prevent responding
224 58 Tobias Brunner
     to renegotiation requested from the other end, so no will be largely ineffective unless both ends agree on it.
225 58 Tobias Brunner
     Also see _reauth_.
226 1 Martin Willi
227 1 Martin Willi
_rekeyfuzz = *100%* | <percentage>_
228 1 Martin Willi
229 31 Martin Willi
p((. maximum percentage by which _marginbytes_, _marginpackets_ and _margintime_ should be randomly increased to randomize
230 1 Martin Willi
     rekeying intervals (important for hosts with many connections); acceptable values are an integer, which may exceed 100,
231 4 Martin Willi
     followed  by  a '%' .
232 23 Tobias Brunner
     The value of _marginTYPE_, after this random increase, must not exceed _lifeTYPE_ (where TYPE is one of bytes, packets or type).
233 23 Tobias Brunner
     The value _0%_ will suppress randomization. Relevant only locally, other end need not agree on it.
234 31 Martin Willi
     Also see [[ExpiryRekey|Expiry and Rekey]].
235 1 Martin Willi
236 1 Martin Willi
237 1 Martin Willi
238 1 Martin Willi
p((.  synonym for _margintime_.
239 1 Martin Willi
240 1 Martin Willi
_reqid = <number>_
241 1 Martin Willi
242 57 Tobias Brunner
p((. sets the reqid for a given connection to a pre-configured fixed value.
243 26 Tobias Brunner
244 57 Tobias Brunner
_tfc = <value>_
245 1 Martin Willi
246 57 Tobias Brunner
p((. number of bytes to pad ESP payload data to. Traffic Flow Confidentiality is currently supported in IKEv2 and applies to outgoing packets only. The special value %mtu fills up ESP packets with padding to have the size of the MTU.
247 57 Tobias Brunner
248 57 Tobias Brunner
_type = *tunnel* | transport | transport_proxy | passthrough | drop_
249 57 Tobias Brunner
250 1 Martin Willi
p((. the type of the connection; currently the accepted values are *tunnel*, signifying a  host-to-host,
251 1 Martin Willi
     host-to-subnet, or subnet-to-subnet tunnel; *transport*, signifying host-to-host transport mode;
252 1 Martin Willi
     *transport_proxy*, signifying the special Mobile IPv6 transport proxy mode;
253 31 Martin Willi
     *passthrough*, signifying that no IPsec processing should be done at all; *drop*, signifying that packets
254 23 Tobias Brunner
     should be  discarded.
255 41 Tobias Brunner
256 34 Tobias Brunner
_xauth = *client* | server_
257 57 Tobias Brunner
258 21 Andreas Steffen
p((. specifies the role in the XAuth protocol if activated by _authby=xauthpsk_ or _authby=xauthrsasig_.
259 1 Martin Willi
260 21 Andreas Steffen
_xauth_identity = <id>_
261 23 Tobias Brunner
262 20 Andreas Steffen
p((. defines the identity/username the client uses to reply to an XAuth request. If not defined, the IKEv1 identity will be used as XAuth identity.
263 53 Tobias Brunner
264 23 Tobias Brunner
265 20 Andreas Steffen
h2. left|right End Parameters
266 1 Martin Willi
267 1 Martin Willi
Connection descriptions are defined in terms of a left endpoint and a right endpoint. For example, the
268 1 Martin Willi
two parameters leftid and rightid specify the identity of the left and the right endpoint. For every
269 52 Tobias Brunner
connection description an attempt is made to figure out whether the local endpoint should act as the left or
270 52 Tobias Brunner
the right endpoint. This is done by matching the IP addresses defined for both endpoints with the
271 1 Martin Willi
IP addresses assigned to local network interfaces. If a match is found then the role (left or right) that
272 1 Martin Willi
matches is going to be considered "local". If no match is found during startup, "left" is considered "local".
273 1 Martin Willi
274 1 Martin Willi
_left|right = <ip address> | <fqdn> | *%any*_
275 52 Tobias Brunner
276 52 Tobias Brunner
p((. (required) the IP address of the participant's public-network interface or one of several magic values.
277 57 Tobias Brunner
     The value _%any_ for the local endpoint signifies an address to be filled in
278 52 Tobias Brunner
     (by automatic keying) during negotiation. If the local peer initiates the connection setup the routing table
279 23 Tobias Brunner
     will be queried to determine the correct local IP address. In case the local peer is responding to a connection
280 1 Martin Willi
     setup then any IP address that is assigned to a local interface will be accepted.
281 1 Martin Willi
282 58 Tobias Brunner
p((. Prior to [[5.0.0]] specifying _%%any_ for the local endpoint was not supported for IKEv1 connections, instead
283 58 Tobias Brunner
     the keyword _%%defaultroute_ could be used, causing the value to be filled in automatically with the local
284 58 Tobias Brunner
     address of the default-route interface (as determined at IPsec startup time and during configuration
285 57 Tobias Brunner
     update). Either left or right may be _%defaultroute_, but not both.
286 57 Tobias Brunner
287 57 Tobias Brunner
p((. The prefix % in front of a fully-qualified domain name or an IP address will implicitly set _left|rightallowany=yes_.
288 1 Martin Willi
289 57 Tobias Brunner
p((. If _%any_ is used for the remote endpoint it literally means any IP address.
290 1 Martin Willi
291 31 Martin Willi
p((. Please note that with the usage of wildcards multiple connection descriptions might match a given incoming
292 33 Tobias Brunner
     connection attempt. The most specific description is used in that case.
293 33 Tobias Brunner
294 33 Tobias Brunner
_left|rightallowany = yes | *no*_
295 1 Martin Willi
296 29 Daniel Mentz
p((. a modifier for _left|right_, making it behave as _%any_ although a concrete IP address has been
297 1 Martin Willi
     assigned. Recommended for dynamic IP addresses that can be resolved by DynDNS at IPsec startup or update time.
298 1 Martin Willi
299 1 Martin Willi
_left|rightauth = <auth method>_
300 1 Martin Willi
301 58 Tobias Brunner
p((. Authentication method to use locally (left) or require from the remote (right) side. Acceptable values are *pubkey*
302 58 Tobias Brunner
     for public key encryption (RSA/ECDSA), *psk* for pre-shared key authentication, *eap* to [require the] use of the Extensible Authentication Protocol, and *xauth* for IKEv1 eXtended Authentication.
303 32 Daniel Mentz
     To require a trustchain public key strength for the remote side, specify the key type followed
304 57 Tobias Brunner
     by the minimum strength iin bits (for example *ecdsa-384* or *rsa-2048-ecdsa-256*).
305 57 Tobias Brunner
     To limit the acceptable set of hashing algorithms for trustchain validation, append hash algorithms
306 57 Tobias Brunner
     to *pubkey* or a key strength definition (for example *pubkey-sha1-sha256* or *rsa-2048-ecdsa-256-sha256-sha384-sha512*).
307 1 Martin Willi
     In the case of *eap*, an optional EAP method can be appended. Currently defined methods are *eap-aka*,
308 58 Tobias Brunner
     *eap-gtc*, *eap-md5*, *eap-mschapv2*, *eap-peap*, *eap-sim*, *eap-tls*, *eap-ttls*, *eap-dynamic*, and *eap-radius*.
309 58 Tobias Brunner
     Alternatively, IANA assigned EAP method numbers are accepted. Vendor specific EAP methods are defined in the form
310 1 Martin Willi
     *eap-type-vendor* (e.g. *eap-7-12345*).
311 1 Martin Willi
     For *xauth*, an XAuth authentication backend can be specified, such as *xauth-generic* or *xauth-eap*. If XAuth is used in _leftauth_, Hybrid authentication is used. For traditional XAuth authentication, define XAuth in _leftauth2_.
312 1 Martin Willi
313 1 Martin Willi
p((. Prior to [[5.0.0]] this parameter is only supported for IKEv2.
314 1 Martin Willi
315 57 Tobias Brunner
316 27 Daniel Mentz
_left|rightauth2 = <auth method>_
317 33 Tobias Brunner
318 58 Tobias Brunner
p((. Same as _left|rightauth_, but defines an additional authentication exchange. In IKEv1, only XAuth can be used
319 58 Tobias Brunner
     in the second authentication round. IKEv2 supports multiple complete authentication rounds using
320 58 Tobias Brunner
     _Multiple Authentication Exchanges_ defined in "RFC 4739": This allows e.g. a separate authentication of host and user.
321 57 Tobias Brunner
322 57 Tobias Brunner
p((. Prior to [[5.0.0]] this parameter is only supported for IKEv2.
323 7 Martin Willi
324 31 Martin Willi
325 57 Tobias Brunner
_left|rightca = <issuer dn> | %same_
326 23 Tobias Brunner
327 57 Tobias Brunner
p((. the distinguished name of a certificate authority which is required to lie in the trust path going from the
328 57 Tobias Brunner
     _left|right_ participant's certificate up to the root certification authority.
329 58 Tobias Brunner
     *%same* means that the value configured for the other participant should be reused.
330 56 Andreas Steffen
331 1 Martin Willi
_left|rightca2 = <issuer dn> | %same_
332 56 Andreas Steffen
333 23 Tobias Brunner
p((. Same as _left|rightca_ but for the second authentication (IKev2 only).
334 21 Andreas Steffen
335 1 Martin Willi
_left|rightcert = <path>_
336 1 Martin Willi
337 1 Martin Willi
p((. the path to the left|right participant's X.509 certificate. The file can be coded either in PEM or DER format.
338 1 Martin Willi
     OpenPGP certificates are supported as well.  Both absolute paths or paths relative to
339 23 Tobias Brunner
     [[IpsecDirectoryCerts|/etc/ipsec.d/certs]] are accepted. By default _left|rightcert_ sets _left|rightid_
340 58 Tobias Brunner
     to the distinguished name of the certificate's subject. The _left|right_ participant's ID can be overridden
341 58 Tobias Brunner
     by specifying a _left|rightid_ value which must be certified by the certificate, though.
342 31 Martin Willi
343 23 Tobias Brunner
_left|rightcert2 = <path>_
344 23 Tobias Brunner
345 57 Tobias Brunner
p((. Same as _left|rightcert_ but for the second authentication round (IKEv2 only).
346 21 Andreas Steffen
347 1 Martin Willi
_left|rightcertpolicy = <OIDs>_
348 33 Tobias Brunner
349 7 Martin Willi
p((. Comma separated list of certificate policy OIDs the peer's certificate must have.
350 1 Martin Willi
     OIDs are specified using the numerical dotted representation (prior to [[5.0.0]] only for IKEv2).
351 1 Martin Willi
352 58 Tobias Brunner
_left|rightdns = <servers>_
353 58 Tobias Brunner
354 58 Tobias Brunner
p((. Comma separated list of DNS server addresses to exchange as configuration attributes. On the initiator,
355 58 Tobias Brunner
     a server is a fixed IPv4/IPv6 address, or _%config4/%config6_ to request attributes without an address.
356 58 Tobias Brunner
     On the responder, only fixed IPv4/IPv6 addresses are allowed and define DNS servers assigned to the client.
357 58 Tobias Brunner
     Available since [[5.0.1]].
358 58 Tobias Brunner
359 1 Martin Willi
_left|rightfirewall = yes | *no*_
360 23 Tobias Brunner
361 1 Martin Willi
p((. whether the _left|right_ participant is doing forwarding-firewalling (including  masquerading)
362 1 Martin Willi
     using iptables for traffic from _left|rightsubnet_, which should be turned off for traffic to the
363 1 Martin Willi
     other subnet) once the connection is established. May not be used in the same connection description with
364 1 Martin Willi
     _left|rightupdown_. Implemented as a parameter to the default _ipsec _updown_ script. Relevant only
365 1 Martin Willi
     locally, other end need not agree on it.
366 1 Martin Willi
367 1 Martin Willi
p((. If one or  both security gateways are doing forwarding firewalling (possibly including masquerading),
368 23 Tobias Brunner
     and this is specified using the firewall parameters, tunnels  established with  IPsec  are exempted from
369 20 Andreas Steffen
     it so that packets can flow unchanged through the tunnels. (This means that all subnets connected in this
370 23 Tobias Brunner
     manner must have distinct, non-overlapping subnet address blocks.)  This is done by the default 
371 57 Tobias Brunner
     _ipsec _updown_ script.
372 1 Martin Willi
373 1 Martin Willi
p((. In situations calling for more control, it may be preferable for the user to supply his own _updown_ script,
374 1 Martin Willi
     which makes the appropriate adjustments for his system.
375 1 Martin Willi
376 1 Martin Willi
_left|rightgroups = <group list>_
377 1 Martin Willi
378 31 Martin Willi
p((. a comma-separated list of group names. If the _left|rightgroups_ parameter is present then the peer must
379 58 Tobias Brunner
     be a member of at least one of the groups defined by the parameter. Groups may be used together with the
380 58 Tobias Brunner
     [[EapRadius#Group-selection|eap-radius]] plugin.
381 57 Tobias Brunner
382 58 Tobias Brunner
_left|rightgroups2 = <group list>_
383 1 Martin Willi
384 58 Tobias Brunner
p((. Same as _left|rightgroups_ but for the second authentication round defined with _left|rightauth2_.
385 58 Tobias Brunner
     Available since [[5.0.1]].
386 58 Tobias Brunner
387 1 Martin Willi
_left|righthostaccess = yes | *no*_
388 1 Martin Willi
389 1 Martin Willi
p((. inserts a pair of INPUT and OUTPUT iptables rules using the default _ipsec _updown_ script,
390 1 Martin Willi
     thus allowing access to the host itself in the case where the host's internal interface is part
391 1 Martin Willi
     of the negotiated client subnet. 
392 33 Tobias Brunner
393 23 Tobias Brunner
_left|rightid = <id>_
394 57 Tobias Brunner
395 57 Tobias Brunner
p((. how the _left|right_ participant should be identified for authentication; defaults to _left|right_ or the subject of the certificate configured with _left|rightcert_.
396 57 Tobias Brunner
     Can be an IP address, a fully-qualified domain name, an email address, or a keyid.
397 33 Tobias Brunner
     Prior to [[5.0.0]] fully-qualified domain names can be preceded by an @ to avoid them being resolved to an IP address.
398 23 Tobias Brunner
399 58 Tobias Brunner
p((. Since [[5.0.1]] _rightid_ for IKEv2 connections optionally takes a % as prefix in front of the identity.
400 58 Tobias Brunner
     If given it prevents the daemon from sending IDr in its IKE_AUTH request and will allow it to verify the 
401 58 Tobias Brunner
     configured identity against the subject and subjectAltNames contained in the responder's certificate (otherwise,
402 58 Tobias Brunner
     it is only compared with the IDr returned by the responder). The IDr sent by the initiator might otherwise 
403 58 Tobias Brunner
     prevent the responder from finding a config if it has configured a different value for _leftid_.
404 58 Tobias Brunner
405 33 Tobias Brunner
_left|rightid2 = <id>_
406 7 Martin Willi
407 23 Tobias Brunner
p((. Identity to use for the second authentication of the left participant (IKEv2 only).
408 23 Tobias Brunner
     Defaults to _left|rightid_.
409 21 Andreas Steffen
410 1 Martin Willi
_leftikeport = <port>_
411 1 Martin Willi
412 58 Tobias Brunner
p((. UDP port the left participant uses for IKE communication. If unspecified, port 500 is used with the port
413 58 Tobias Brunner
     floating to 4500 if a NAT is detected or MOBIKE is enabled.
414 1 Martin Willi
     Specifying a local IKE port different from the default additionally requires a socket implementation that
415 1 Martin Willi
     listens to this port.
416 58 Tobias Brunner
     Only supported for IKEv2 prior to [[5.0.0]].
417 1 Martin Willi
418 1 Martin Willi
_left|rightprotoport = <protocol>/<port>_
419 1 Martin Willi
420 1 Martin Willi
p((. restrict the traffic selector to a single protocol and/or port. Examples: _leftprotoport=tcp/http_
421 58 Tobias Brunner
     or _leftprotoport=6/80_ or _leftprotoport=udp_ or _leftprotoport=/53_. Instead of omitting either value
422 58 Tobias Brunner
     *%any* can be used to the same effect, e.g. _leftprotoport=udp/%any_ or _leftprotoport=%any/53_.
423 1 Martin Willi
424 58 Tobias Brunner
_left|rightrsasigkey = <raw rsa public key> | <path to public key>_
425 1 Martin Willi
426 58 Tobias Brunner
p((. the left|right participant's public key for RSA signature authentication, in RFC 2537 format using hex (0x prefix)
427 58 Tobias Brunner
     or base64 (0s prefix) encoding. Also accepted is the path to a file containing the public key in PEM or DER encoding.
428 1 Martin Willi
429 1 Martin Willi
_left|rightsendcert = never | no | *ifasked* | always | yes_
430 1 Martin Willi
431 1 Martin Willi
p((. Accepted values are *never* or *no*, *always* or *yes*, and *ifasked*, the latter meaning that 
432 1 Martin Willi
     the peer must send a certificate request (CR) payload in order to get a certificate in return.
433 1 Martin Willi
434 58 Tobias Brunner
_leftsourceip = %config4 | %config6 | <ip address>_
435 1 Martin Willi
436 1 Martin Willi
p((. The internal source IP to use in a tunnel, also known as [[VirtualIp|virtual IP]].
437 58 Tobias Brunner
     If the value is one of the synonyms _%config_, _%cfg_, _%modeconfig_ or _%modecfg_, an address (from
438 58 Tobias Brunner
     the tunnel address family) is requested from the peer.
439 58 Tobias Brunner
     Since [[5.0.1]] a comma-separated list is accepted to request multiple addresses, and with _%config4_ and
440 58 Tobias Brunner
     _%config6_ an address of the given address family will be requested explicitly.
441 58 Tobias Brunner
     If an IP address is configured, it will be requested from the responder, which is free to respond with a
442 58 Tobias Brunner
     different address.
443 31 Martin Willi
444 23 Tobias Brunner
_rightsourceip = %config | <network>/<netmask> | %poolname_
445 57 Tobias Brunner
446 7 Martin Willi
p((. The internal source IP to use in a tunnel for the remote peer. If the value is %config on the responder
447 23 Tobias Brunner
     side, the initiator must propose an address which is then echoed back. Also supported are address pools
448 31 Martin Willi
     expressed as _<network>/<netmask>_ or the use of an external IP address pool using _%%poolname_ where
449 58 Tobias Brunner
     _poolname_ is the name of the IP address pool used for the lookup (see [[VirtualIp|virtual IP]] for details).
450 58 Tobias Brunner
     Since [[5.0.1]] a comma-separated list of IP addresses / pools is accepted, for instance, to define pools of
451 58 Tobias Brunner
     different address families. 
452 57 Tobias Brunner
453 1 Martin Willi
_left|rightsubnet = <ip subnet>_
454 57 Tobias Brunner
455 58 Tobias Brunner
p((. private subnet behind the left participant, expressed as network/netmask; if omitted, essentially assumed
456 58 Tobias Brunner
     to be _left_/32|128, signifying that the _left|right_ end of the connection goes to the _left|right_ participant only.
457 58 Tobias Brunner
     The configured subnets of the peers may differ, the protocol narrows it to the greatest common subnet.
458 58 Tobias Brunner
     Since [[5.0.0]] this is also done for IKEv1, but as this may lead to problems with other implementations,
459 58 Tobias Brunner
     make sure to configure identical subnets in such configurations.
460 58 Tobias Brunner
     IKEv2 supports multiple subnets separated by commas, IKEv1 only interprets the first subnet of such a definition,
461 58 Tobias Brunner
     unless the Cisco Unity extension plugin is enabled (available since [[5.0.1]]). 
462 23 Tobias Brunner
463 21 Andreas Steffen
_left|rightupdown = <path>_
464 1 Martin Willi
465 31 Martin Willi
p((. what _updown_ script to run to adjust routing and/or firewalling when the status of the connection
466 1 Martin Willi
     changes (default _ipsec _updown_). Relevant only locally, other end need not agree on it.
467 33 Tobias Brunner
     Charon uses the _updown_ script to insert firewall rules only, since routing has been implemented directly
468 33 Tobias Brunner
     into the daemon.
469 33 Tobias Brunner
470 33 Tobias Brunner
h2. IKEv2 Mediation Extension Parameters
471 33 Tobias Brunner
472 33 Tobias Brunner
The following parameters are relevant to IKEv2 Mediation Extension operation only.
473 33 Tobias Brunner
474 23 Tobias Brunner
_mediation = yes | *no*_
475 23 Tobias Brunner
476 31 Martin Willi
p((. whether this connection is a mediation connection,  ie.  whether this connection is used to mediate other
477 57 Tobias Brunner
     connections.  Mediation connections create no child SA. Acceptable values  are  no (the default) and yes.
478 57 Tobias Brunner
479 57 Tobias Brunner
_mediated_by = <name>_
480 57 Tobias Brunner
481 57 Tobias Brunner
p((. the  name  of the connection to mediate this connection through. If given, the connection will  be  mediated
482 21 Andreas Steffen
     through  the  named mediation  connection.  The mediation connection must set *mediation=yes*.
483 1 Martin Willi
484 31 Martin Willi
_me_peerid = <id>_
485 1 Martin Willi
486 57 Tobias Brunner
p((. ID as which the peer is known to the mediation server, ie. which the  other end of this connection uses as
487 1 Martin Willi
     its leftid on its connection to the mediation server.  This is the ID we request  the mediation server to
488 1 Martin Willi
     mediate us with.  If me_peerid is not given, the rightid of this connection will be used as peer ID.
489 58 Tobias Brunner
490 58 Tobias Brunner
h2. Removed parameters (since 5.0.0)
491 58 Tobias Brunner
492 58 Tobias Brunner
_auth = *esp* | ah_
493 58 Tobias Brunner
494 58 Tobias Brunner
p((. whether authentication should be done as part of ESP encryption, or separately using the AH protocol.
495 58 Tobias Brunner
	Only supported by the IKEv1 daemon pluto.
496 58 Tobias Brunner
497 58 Tobias Brunner
_pfs = *yes* | no_
498 58 Tobias Brunner
499 58 Tobias Brunner
p((. whether _Perfect Forward Secrecy_ of keys is desired on the connection's keying channel (with PFS,
500 58 Tobias Brunner
     penetration of the key-exchange protocol does not compromise keys negotiated earlier). IKEv2 always uses
501 58 Tobias Brunner
     PFS for IKE_SA rekeying whereas for CHILD_SA rekeying PFS is enforced by defining a Diffie-Hellman dhgroup
502 58 Tobias Brunner
     in the _esp_ parameter.  Since [[5.0.0]] the latter also applies to IKEv1 and this parameter has no effect anymore.
503 58 Tobias Brunner
504 58 Tobias Brunner
_pfsgroup = <modp group>_
505 58 Tobias Brunner
506 58 Tobias Brunner
p((. defines a Diffie-Hellman group for _perfect forward secrecy_ in IKEv1 Quick Mode differing from the DH group
507 58 Tobias Brunner
     used for IKEv1 Main Mode (IKEv1 pluto daemon only).
508 58 Tobias Brunner
509 58 Tobias Brunner
_left|rightnexthop = %direct | %defaultroute | <ip address> | <fqdn>_
510 58 Tobias Brunner
511 58 Tobias Brunner
p((. This parameter is usually not needed any more because the NETKEY IPsec stack does not require
512 58 Tobias Brunner
     explicit routing entries for the traffic to be tunneled. If _left|sourceip_ is used with IKEv1
513 58 Tobias Brunner
     then _left|rightnexthop_ must still be set in order for the source routes to work properly.
514 58 Tobias Brunner
515 58 Tobias Brunner
_left|rightsubnetwithin = <ip subnet>_
516 58 Tobias Brunner
517 58 Tobias Brunner
p((. the  peer can propose any subnet or single IP address that fits within the range defined by
518 58 Tobias Brunner
     _left|rightsubnetwithin_.  Is a synonym for _left|rightsubnet_ since [[5.0.0]], as subnets are narrowed.